Comnet CNGE2FE8MSPOE Technical Information Seite 27
- Seite / 162
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
20
3.6 Cabling
Use four twisted-pair, Category 5e or above cabling for RJ45 port connection. The
cable between the switch and the link partner (switch, hub, workstation, etc.) must be
less than 100 meters (328 ft.) long.
Fiber segment using single-mode connector type must use 9/125 µm single-mode
fiber cable. User can connect two devices in the distance up to 30km.
Fiber segment using multi-mode connector type must use 50 or 62.5/125 µm multi-
mode fiber cable. User can connect two devices up to 2km distances.
Gigabit Copper/SFP (mini-GBIC) combo port:
The Industrial switch has the auto-detected Giga port—Gigabit Copper/SFP combo ports.
The Gigabit Copper (10/100/1000T) ports should use Category 5e or above UTP/STP cable
for the connection up to 1000Mbps. The small form-factor pluggable (SFP) is a compact
optical transceiver used in optical communications for both telecommunication and data
communications. The SFP slots supporting dual mode can switch the connection speed
between 100 and 1000Mbps. They are used for connecting to the network segment with
single or multi-mode fiber. You can choose the appropriate SFP transceiver to plug into the
slots. Then use proper multi-mode or single-mode fiber according to the transceiver. With
fiber optic, it transmits at speed up to 1000 Mbps and you can prevent noise interference
from the system.
Note
The SFP/Copper Combo port can’t both work at the same time. The SFP port
has the higher priority than copper port; if you insert the 1000M SFP
transceiver (which has connected to the remote device via fiber cable) into the
SFP port, the connection of the accompanying copper port will link down.
If you insert the 100M SFP transceiver into the SFP port even without a fiber
connection to the remote, the connection of the accompanying copper port will
link down immediately.
- CNGE2FE8MSPOE 1
- FCC Warning 2
- CE Mark Warning 2
- Content 3
- Chapter 1 Introduction 8
- 1.2 Software Features 12
- 1.3 Package Contents 15
- 2.1 Physical Dimension 16
- 2.2 Front Panel 16
- 2.3 Top View 17
- 2.4 LED Indicators 18
- 3.1 Installation Steps 20
- 3.2 DIN-Rail Mounting 21
- 3.4 Wiring the Power Inputs 25
- 3.6 Cabling 27
- Transceiver Inserted 28
- Remove LC connector 30
- 4.1 X-Ring Application 33
- 4.3 Dual Homing Application 35
- Chapter 5 Console Management 36
- Console login interface 38
- 5.4 CLI Management 39
- 5.5 Commands Level 39
- 6.3 System Login 42
- 6.4 System Information 43
- 6.5 IP Configuration 44
- IP configuration interface 45
- 6.6 DHCP Server 46
- 6.6.1 System configuration 47
- 6.6.2 Client Entries 48
- 6.6.3 Port and IP Bindings 49
- 6.7 TFTP 50
- 6.7.2 Restore Configuration 51
- 6.7.3 Backup Configuration 52
- 6.8 System Event Log 53
- SMTP Configuration interface 56
- 6.9 Fault Relay Alarm 59
- 6.10 SNTP Configuration 60
- SNTP Configuration interface 63
- 6.11 IP Security 64
- IP Security interface 65
- 6.12 User Authentication 66
- 6.13 Port Statistics 67
- Port Statistics interface 68
- 6.14 Port Control 69
- Port Control interface 70
- 6.15 Port Trunk 71
- LACP disabled 73
- LACP enabled 75
- 6.15.3 State Activity 79
- State Activity of Switch 2 80
- 6.16 Port Mirroring 81
- 6.17 Rate Limiting 82
- 6.18 VLAN configuration 84
- 6.18.1 Port-based VLAN 85
- 6.18.2 802.1Q VLAN 88
- 802.1Q Configuration 89
- Group Configuration 91
- 6.19 Rapid Spanning Tree 93
- 6.19.2 Port Configuration 95
- 6.20 SNMP Configuration 97
- 6.20.2 Trap Configuration 99
- 6.20.3 SNMPV3 Configuration 100
- 6.21 QoS Configuration 103
- QoS Configuration interface 104
- 6.21.2 Port-based Priority 105
- 6.21.3 COS Configuration 105
- 6.21.4 TOS Configuration 105
- 6.22 IGMP Configuration 107
- IGMP Configuration interface 108
- 6.23 X-Ring 109
- X-ring Interface 110
- 6.24 LLDP Configuration 111
- 6.25.1 System Configuration 112
- 6.25.2 Port Configuration 114
- 6.25.3 Misc Configuration 116
- 6.26 MAC Address Table 117
- 6.26.2 MAC Filtering 119
- 6.26.3 All MAC Addresses 120
- 6.27 Power over Ethernet 123
- 6.28 Factory Default 125
- 6.29 Save Configuration 126
- 6.30 System Reboot 127
- Troubles shooting 128
- RJ45 Pin Assignments 129
- Cross over cable schematic 130
- Cross over cables schematic 132
- RJ45 Pin Assignment of PoE 133
- Appendix B—Command Sets 135
- Halt and perform a cold 136
- Port Commands Set 138
- Trunk Commands Set 141
- VLAN Commands Set 142
- Spanning Tree Commands Set 144
- QOS Commands Set 147
- IGMP Commands Set 147
- LLDP Commands Set 149
- SNMP Commands Set 150
- Port Mirroring Commands Set 152
- 802.1x Commands Set 153
- TFTP Commands Set 155
- SNTP Commands Set 159
- X-ring Commands Set 160
- PoE Commands Set 161
- Communication Networks 162
Verwandte Produkte und Handbücher für Vernetzung Comnet CNGE2FE8MSPOE
Vernetzung Comnet CNGE3FE7MS4 Technical Information
(104 Seiten)
(104 Seiten)
Vernetzung Comnet CNGE24MS Spezifikationen
(108 Seiten)
(108 Seiten)
Vernetzung Comnet CWGE28FX4TX24MS Spezifikationen
(117 Seiten)
(117 Seiten)
Vernetzung Comnet CNGE24MS Bedienungsanleitung
(82 Seiten)
(82 Seiten)
Evco PM100A manuals
Owner’s manuals and user’s guides for Hardware Evco PM100A.
We providing 1 pdf manuals Evco PM100A for download free by document types: User Manual
Kommentare zu diesen Handbüchern