Comnet CWGE2FE8MSPOE Technical Information Seite 8
- Seite / 143
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
1
Introduction
Power-over-Ethernet (PoE) eliminates the need to run VAC power to other devices on a
wired LAN. Using a Power-over-Ethernet system installers needs to run only a single
Category 5 Ethernet cable that carries both power and data to each device. This allows
greater flexibility in the location of network devices and significantly decreases installation
costs in many cases.
There are two system components in PoE—the Power Sourcing Equipment (PSE) initiates
the connection to the second component, and the Powered Device (PD). The current is
transmitted over two of the four twisted pairs of wires in a Category-5 cable.
Power over Ethernet (PoE) follows the IEEE 802.3af standard and is completely compatible
with existing Ethernet switches and networked devices. Because the Power Sourcing
Equipment (PSE) tests whether a networked device is PoE-capable, power is never
transmitted unless a Powered Device is at other end of the cable. It also continues to
monitor the channel. If the Powered Device does not draw a minimum current, because it
has been unplugged or physically turned off, the PSE shuts down the power to that port.
Optionally, the standard permits Powered Devices to signal to the PSEs exactly how much
power they need.
The CWGE2FE8MSPOE Managed Switch is one of the ComWorx multi-port switches that
can be used to build high-performance switched workgroup networks. Any one of the
switches is a store-and-forward device that offers low latency for high-speed networking. It
also features a “store-and-forward “switching scheme. This allows the switch to auto-learn
and store source addresses in an 8K-entry MAC address table. The switch is targeted at
workgroup, department or backbone computing environment.
- CWGE2FE8MSPOE 1
- FCC Warning 2
- CE Mark Warning 2
- Content 3
- Introduction 8
- Features 9
- Hardware Feature 11
- Software Feature 14
- Package Contents 17
- Hardware Description 18
- available with a 19
- Rear Panel 20
- Desktop Installation 21
- Power On 21
- Network Application 22
- Segment Bridge 23
- Console Management 24
- CLI Management 25
- Commands Set List 27
- System Commands Set 27
- Halt and perform a cold 28
- Port Commands Set 30
- Trunk Commands Set 34
- VLAN Commands Set 35
- QOS Commands Set 41
- IGMP Commands Set 42
- SNMP Commands Set 44
- Port Mirroring Commands Set 47
- 802.1x Commands Set 48
- TFTP Commands Set 51
- PoE Commands Set 51
- SNTP Commands Set 55
- X-ring Commands Set 56
- Web-Based Management 58
- System Login 59
- System Information 60
- IP Configuration 61
- DHCP Configuration 62
- DHCP Server Configuration 63
- DHCP Client Entries 64
- Port and IP Binding 65
- TFTP - Update Firmware 66
- TFTP - Restore Configuration 67
- TFTP - Backup Configuration 68
- SMTP Configuration interface 72
- SNTP Configuration 75
- SNTP Configuration interface 77
- IP Security 78
- IP Security interface 79
- User Authentication 80
- Port Statistics 81
- Port Statistics interface 82
- Port Control 83
- Port Control interface 84
- Port Trunk 85
- LACP disabled 87
- LACP enabled 89
- Port Trunk—State Activity 93
- State Activity of Switch 2 94
- Port Mirroring 95
- Rate Limiting 96
- VLAN configuration 97
- VLAN – Port Based interface 98
- 802.1Q VLAN 101
- 802.1Q Configuration 102
- Group Configuration 104
- Rapid Spanning Tree 106
- RSTP—Port Configuration 109
- SNMP Configuration 111
- Trap Configuration 113
- SNMPv3 Configuration 114
- QoS Configuration 117
- QoS Configuration interface 118
- Port-Based Priority 119
- COS Configuration 119
- TOS Configuration 119
- IGMP Configuration 120
- IGMP Configuration interface 121
- X-ring Interface 123
- LLDP Interface 124
- Multicast Filtering 125
- System Configuration 126
- 802.1x Port Configuration 128
- Misc Configuration 129
- MAC Address Table 131
- MAC Filtering 132
- All MAC Addresses 133
- All MAC Address interface 134
- Power over Ethernet 135
- Factory Default 137
- Save Configuration 137
- System Reboot 138
- Problem Solving 139
- Appendix 141
- Communication Networks 143
Verwandte Produkte und Handbücher für Vernetzung Comnet CWGE2FE8MSPOE
(7 Seiten)
Vernetzung Comnet CNGE24MS Bedienungsanleitung
(82 Seiten)
(82 Seiten)
Evco PM100A manuals
Owner’s manuals and user’s guides for Hardware Evco PM100A.
We providing 1 pdf manuals Evco PM100A for download free by document types: User Manual
Kommentare zu diesen Handbüchern